EVER JOY · CONVEYOR COMPONENTS
Conveyor Idlers & Idler Sets
Mining · Aggregates · Ports · Cement · Bulk Handling
EVER JOY supplies conveyor belt idler rollers and idler sets for new installations and replacement projects. Roller shell, shaft, bearings, seals, mounting ends and idler-set geometry are selected together for the intended belt conveyor duty.

Product Overview
Individual idlers support the carrying or return strand of the belt. Replacement rollers require the correct shaft-end arrangement. Complete idler sets also require matching trough angles, frames, hole centres and mounting heights. Idlers are not drive drum pulleys or complete conveyor systems.
Critical Selection Data
| PARAMETER | SELECTION POINT |
|---|---|
| Roller OD D | Match belt speed, duty and conveyor width |
| Shell length L | Match belt width, set design and frame |
| Bearings & seals | Select for dust, water, speed and service life |
| Mounting fit | Verify flats, shaft length, slots and frame holes |
Main Idler Configurations
Final configuration, covering material and frame design are defined by approved drawings and the purchase specification.
| IDLER TYPE | FUNCTION / SELECTION |
|---|---|
| Carrying idler | Supports the carrying strand, individually or in a troughed set. |
| Return idler | Supports the return strand; flat, V-return and anti-build-up options. |
| Impact idler | Used at loading zones, commonly fitted with impact rubber rings. |
| Self-aligning idler set | Pivoting/guiding arrangement to help control belt mistracking. |
| Disc return idler | Disc geometry reduces material build-up on return strand. |
| Coated idler | Cover material is selected by duty; colour is not a material specification. |
Actual Products & Assembly



Illustrated Products: Impact Roller, Troughed Set & Bearing Section

Three-Roll Troughed Idler Set
Construction & Installation Dimensions

| CODE | DIMENSION |
|---|---|
| D | Roller shell outside diameter; impact rings excluded |
| L | Working face / shell length |
| S | Overall shaft length, end to end |
| E₁/E₂ | Shaft extension beyond shell on each side |
| d | Shaft-end diameter; stepped shafts need separate dimensions |
| F | Across-flats / slot-fitting or other shaft-end geometry |
| A/B | For sets: frame pitch, overall width, installation height and trough angle |
Typical Axial Section

1. Shell 2. Stationary shaft 3. Bearing housing 4. Bearing 5. End seal
Common Sizes & Selection Reference
| PARAMETER | REFERENCE / VALUE |
|---|---|
| Common shell OD D (mm) | 63.5 / 76 / 89 / 102 / 108 / 114 / 127 / 133 / 159 / 194 / 219 |
| Typical shaft OD d (mm) | 20 / 25 / 30 / 35 / 40; verify load and bearing design |
| Typical wall thickness t (mm) | 2.5–5.0 reference; subject to load/structural design |
| Bearing examples | 6204 / 6205 / 6305 / 6206 / 6306 / 6207 / 6307 / 6308 |
| Typical carrying trough angles | 20° / 30° / 35° / 45°; specials to drawing |
| Shell finish / sealing | Steel, coated or impact-ring constructions; seals per duty |
DTII vs TD75: Roller Shell & Overall Shaft Lengths (mm)
DTII — three-roll troughing carrier and single flat-return roller
| Belt BW | Example roller OD D / shaft d | Carry shell L | Carry shaft S | Return shell L | Return shaft S |
|---|---|---|---|---|---|
| 500 | 89 / 20 | 200 | 228 | 600 | 628 |
| 650 | 89 / 20 | 250 | 278 | 750 | 778 |
| 800 | 89 / 20 | 315 | 343 | 950 | 978 |
| 1000 | 108 / 25 | 380 | 414 | 1150 | 1184 |
| 1200 | 133 / 25 | 465 | 499 | 1400 | 1434 |
| 1400 | 133 / 25 | 530 | 564 | 1600 | 1634 |
| 1600 | 133 / 30 | 600 | 642 | 1800 | 1842 |
TD75 — three-roll troughing carrier and single flat-return roller
| Belt BW | Example roller OD D / shaft d | Carry shell L | Carry shaft S | Return shell L | Return shaft S |
|---|---|---|---|---|---|
| 500 | 89 / 20 | 190 | 220 | 600 | 640 |
| 650 | 89 / 20 | 240 | 270 | 750 | 790 |
| 800 | 89 / 20 | 305 | 335 | 950 | 990 |
| 1000 | 108 / 25 | 375 | 408 | 1150 | 1200 |
| 1200 | 108 / 25 | 455 | 488 | 1400 | 1450 |
| 1400 | 108 / 25 | 525 | 558 | 1600 | 1650 |
Standards, Inspection & Delivery
Standards by Intended Scope
| STANDARD | SCOPE |
|---|---|
| GB/T 10595-2017 | Chinese belt-conveyor standard with idler requirements and test methods. |
| ISO 1537:1975 | Dimensions, arrangement and clearance for certain three-roll troughed idlers; confirmed in 2025. |
| DIN 22107 / DIN 22112 series | Engineering references for relevant idler geometry, components and tests. |
| CEMA 502-2022 | North American guidance for troughing/return idler classes, geometry and selection. |
Inspection Items to Agree in the Purchase Specification
| CHECK | WHAT TO CHECK |
|---|---|
| Dimensional inspection | D, L, S, E, d, F, wall thickness and end form |
| Radial runout | Accept according to length, speed and specified standard |
| Rotational resistance | Test under stated roller load and speed |
| Axial displacement / load | Evaluate assembly retention and axial movement |
| Sealing performance | Check dust and water ingress resistance |
| Bearing operation | Noise, vibration, stiffness and abnormal heating |
| Finish / packing | Weld quality, coating, corrosion protection and shipment protection |
Illustrative standard criterion: GB/T 10595-2017 specifies a maximum axial displacement of 0.7 mm under 500 N axial load in the stated idler test. This is not an assertion that every model shown has a passing test certificate.
Applications, FAQ & Request for Quotation
Typical projects include mining (surface and underground requirements to be assessed separately), aggregate crushing and screening, cement, coal, ports, metallurgy and industrial bulk conveying. Heavy dust, rain, high impact, fast belts and continuous long-distance operation require separate bearing-life and sealing decisions.
Frequently Asked Questions
01 What is the difference between a roller and an idler set?
A roller is one rotating unit with bearings; an idler set includes rollers and their matching frame. State the required supply scope.
02 Can you quote from belt width only?
It allows preliminary sizing only. A firm quotation needs D, L, shaft ends, trough angle and quantity.
03 Does a red roller necessarily mean polyurethane?
No. Colour does not identify coating type, wear grade or corrosion resistance. Specify the material.
04 Can the rollers be made to a drawing or sample?
Drawing-based or sample-based requirements can be assessed. Shaft ends and centre dimensions are essential.
05 Can I specify a 6204 or 6306 bearing?
Bearing choice must match shaft size, operating load, speed, life and sealing design.
06 Can rollers and frames be ordered together?
Yes, for an engineered idler set. Confirm pitch, mounting height, trough angle and shaft-end fit.
07 Can inspection records be supplied?
Inspection and documentation requirements should be agreed for each order; this brochure is not a test certificate.
08 How are idlers packed for export?
Strapping, pallets or cases are chosen to suit quantities, weight, shaft-end protection and shipping conditions.
RFQ Checklist
- Individual rollers or complete idler assemblies
- Belt width, speed, conveyed material and loading
- Roller OD D, shell L, overall shaft S, shaft OD d
- Shaft flats F, extensions E and old-unit drawings/photos
- Bearing, seal, surface finish, trough angle and frame drawing
- Quantity, operating environment, destination and acceptance standard
EVER JOY supports industrial conveyor component production and export delivery from its manufacturing base in Guzhen County, Bengbu, Anhui, China. Final configurations, quantities and inspection provisions are agreed by contract and approved drawings.

