EVER JOY · CONVEYOR COMPONENTS

Conveyor Idlers & Idler Sets

Русский

Mining · Aggregates · Ports · Cement · Bulk Handling

EVER JOY supplies conveyor belt idler rollers and idler sets for new installations and replacement projects. Roller shell, shaft, bearings, seals, mounting ends and idler-set geometry are selected together for the intended belt conveyor duty.

EVER JOY finished conveyor idlers and packed product
EVER JOY finished conveyor idlers and packed product

Product Overview

Individual idlers support the carrying or return strand of the belt. Replacement rollers require the correct shaft-end arrangement. Complete idler sets also require matching trough angles, frames, hole centres and mounting heights. Idlers are not drive drum pulleys or complete conveyor systems.

Critical Selection Data

PARAMETERSELECTION POINT
Roller OD DMatch belt speed, duty and conveyor width
Shell length LMatch belt width, set design and frame
Bearings & sealsSelect for dust, water, speed and service life
Mounting fitVerify flats, shaft length, slots and frame holes
Indicative values aid preliminary selection; final product dimensions follow the agreed specification and approved drawing.

Main Idler Configurations

Final configuration, covering material and frame design are defined by approved drawings and the purchase specification.

IDLER TYPEFUNCTION / SELECTION
Carrying idlerSupports the carrying strand, individually or in a troughed set.
Return idlerSupports the return strand; flat, V-return and anti-build-up options.
Impact idlerUsed at loading zones, commonly fitted with impact rubber rings.
Self-aligning idler setPivoting/guiding arrangement to help control belt mistracking.
Disc return idlerDisc geometry reduces material build-up on return strand.
Coated idlerCover material is selected by duty; colour is not a material specification.

Actual Products & Assembly

Finished red-coated idlers and export packing
Finished red-coated idlers and export packing

Illustrated Products: Impact Roller, Troughed Set & Bearing Section

Illustrations show representative product forms and internal components, not factory photographs or approved engineering drawings. Actual rings, bearings, seals and frame dimensions follow the agreed product specification.

Construction & Installation Dimensions

Single-roller dimensional schematic — not to scale; verify each shaft end against the approved drawing
Single-roller dimensional schematic — not to scale; verify each shaft end against the approved drawing
CODEDIMENSION
DRoller shell outside diameter; impact rings excluded
LWorking face / shell length
SOverall shaft length, end to end
E₁/E₂Shaft extension beyond shell on each side
dShaft-end diameter; stepped shafts need separate dimensions
FAcross-flats / slot-fitting or other shaft-end geometry
A/BFor sets: frame pitch, overall width, installation height and trough angle

Typical Axial Section

Typical steel idler section: shell, stationary shaft, end housings, bearings and seals (schematic only)
Typical steel idler section: shell, stationary shaft, end housings, bearings and seals (schematic only)

1. Shell 2. Stationary shaft 3. Bearing housing 4. Bearing 5. End seal

Common Sizes & Selection Reference

The following are public-standard and industry reference configurations—not a statement that every EVER JOY size is stocked or certified. Dimensions are finalized by an approved drawing.
PARAMETERREFERENCE / VALUE
Common shell OD D (mm)63.5 / 76 / 89 / 102 / 108 / 114 / 127 / 133 / 159 / 194 / 219
Typical shaft OD d (mm)20 / 25 / 30 / 35 / 40; verify load and bearing design
Typical wall thickness t (mm)2.5–5.0 reference; subject to load/structural design
Bearing examples6204 / 6205 / 6305 / 6206 / 6306 / 6207 / 6307 / 6308
Typical carrying trough angles20° / 30° / 35° / 45°; specials to drawing
Shell finish / sealingSteel, coated or impact-ring constructions; seals per duty

DTII vs TD75: Roller Shell & Overall Shaft Lengths (mm)

DTII — three-roll troughing carrier and single flat-return roller

Belt BWExample roller OD D / shaft dCarry shell LCarry shaft SReturn shell LReturn shaft S
50089 / 20200228600628
65089 / 20250278750778
80089 / 20315343950978
1000108 / 2538041411501184
1200133 / 2546549914001434
1400133 / 2553056416001634
1600133 / 3060064218001842

TD75 — three-roll troughing carrier and single flat-return roller

Belt BWExample roller OD D / shaft dCarry shell LCarry shaft SReturn shell LReturn shaft S
50089 / 20190220600640
65089 / 20240270750790
80089 / 20305335950990
1000108 / 2537540811501200
1200108 / 2545548814001450
1400108 / 2552555816001650
Dimensional notes: L = individual roller shell/face length; S = overall end-to-end shaft length; D = roller OD and d = shaft OD for the stated example configuration. The rows are typical combinations from public series catalogues, not the only sizes available for each belt width. The carrying columns refer to each roller in a three-roll troughing set; the return columns refer only to a single flat return roller, not a V-return set. Shaft length can change with OD, shaft size, end design and revision. Verify E₁/E₂ extensions, flat width F, bearing selection and frame-slot fit against the approved drawing. TD75 reference shown for common 500–1400 mm widths only; DTII 1600 mm dimensions must not be assumed interchangeable.
Bearing-bore examples: Ø20→6204; Ø25→6205/6305; Ø30→6206/6306; Ø35→6207/6307; Ø40→6208/6308. Final bearings require load, speed, life and sealing verification.

Standards, Inspection & Delivery

Standards by Intended Scope

STANDARDSCOPE
GB/T 10595-2017Chinese belt-conveyor standard with idler requirements and test methods.
ISO 1537:1975Dimensions, arrangement and clearance for certain three-roll troughed idlers; confirmed in 2025.
DIN 22107 / DIN 22112 seriesEngineering references for relevant idler geometry, components and tests.
CEMA 502-2022North American guidance for troughing/return idler classes, geometry and selection.

Inspection Items to Agree in the Purchase Specification

CHECKWHAT TO CHECK
Dimensional inspectionD, L, S, E, d, F, wall thickness and end form
Radial runoutAccept according to length, speed and specified standard
Rotational resistanceTest under stated roller load and speed
Axial displacement / loadEvaluate assembly retention and axial movement
Sealing performanceCheck dust and water ingress resistance
Bearing operationNoise, vibration, stiffness and abnormal heating
Finish / packingWeld quality, coating, corrosion protection and shipment protection
STANDARD EXAMPLE
Illustrative standard criterion: GB/T 10595-2017 specifies a maximum axial displacement of 0.7 mm under 500 N axial load in the stated idler test. This is not an assertion that every model shown has a passing test certificate.
Standards and dimensions: GB/T 10595-2017, ISO 1537:1975, CEMA 502-2022 and DIN 22107/22112; DTII / TD75 shell and shaft lengths are illustrative values from public series catalogues.

Applications, FAQ & Request for Quotation

Typical projects include mining (surface and underground requirements to be assessed separately), aggregate crushing and screening, cement, coal, ports, metallurgy and industrial bulk conveying. Heavy dust, rain, high impact, fast belts and continuous long-distance operation require separate bearing-life and sealing decisions.

Frequently Asked Questions

01 What is the difference between a roller and an idler set?

A roller is one rotating unit with bearings; an idler set includes rollers and their matching frame. State the required supply scope.

02 Can you quote from belt width only?

It allows preliminary sizing only. A firm quotation needs D, L, shaft ends, trough angle and quantity.

03 Does a red roller necessarily mean polyurethane?

No. Colour does not identify coating type, wear grade or corrosion resistance. Specify the material.

04 Can the rollers be made to a drawing or sample?

Drawing-based or sample-based requirements can be assessed. Shaft ends and centre dimensions are essential.

05 Can I specify a 6204 or 6306 bearing?

Bearing choice must match shaft size, operating load, speed, life and sealing design.

06 Can rollers and frames be ordered together?

Yes, for an engineered idler set. Confirm pitch, mounting height, trough angle and shaft-end fit.

07 Can inspection records be supplied?

Inspection and documentation requirements should be agreed for each order; this brochure is not a test certificate.

08 How are idlers packed for export?

Strapping, pallets or cases are chosen to suit quantities, weight, shaft-end protection and shipping conditions.

RFQ Checklist

  • Individual rollers or complete idler assemblies
  • Belt width, speed, conveyed material and loading
  • Roller OD D, shell L, overall shaft S, shaft OD d
  • Shaft flats F, extensions E and old-unit drawings/photos
  • Bearing, seal, surface finish, trough angle and frame drawing
  • Quantity, operating environment, destination and acceptance standard

EVER JOY supports industrial conveyor component production and export delivery from its manufacturing base in Guzhen County, Bengbu, Anhui, China. Final configurations, quantities and inspection provisions are agreed by contract and approved drawings.

Contact EVER JOY

info@everjoyconveyor.com · WhatsApp: +86 15175229655

en_USEnglish
Scroll to Top